一、双组份打胶机的显著优势：让胶水发挥最大威力

1、 The significant advantage of two-component gluing machine: allowing the glue to exert its maximum power

1. 混合精准，效果稳定

1. Accurate mixing and stable effect

人工调胶时，很难准确控制两种胶水的比例，常常出现 A 胶多了粘不牢、B 胶多了易脆裂的情况。而双组份打胶机通过传感器和控制系统，将比例误差控制在 1% 以内，比如设定 10:1 的比例时，每 10 份 A 胶必定搭配 1 份 B 胶，确保胶水固化后具有稳定的弹性和粘结力。在门窗密封中，这种精准混合的胶水能有效抵御风雨侵蚀，使用寿命比人工调胶延长 30% 以上。

When manually adjusting the glue, it is difficult to accurately control the ratio of the two types of glue, often resulting in situations where too much glue A cannot stick firmly and too much glue B is prone to brittle cracking. The two-component glue machine controls the proportion error within 1% through sensors and control systems. For example, when setting a ratio of 10:1, every 10 parts of A glue must be paired with 1 part of B glue to ensure stable elasticity and bonding strength after the glue is cured. In door and window sealing, this precisely mixed adhesive can effectively resist wind and rain erosion, and its service life is extended by more than 30% compared to manual glue adjustment.

2. 高效省力，提升速度

2. Efficient and labor-saving, improving speed

传统人工调胶不仅费时，还需要频繁搅拌，而打胶机可以连续作业，每分钟能挤出几十米长的胶条。比如在玻璃幕墙安装中，一台打胶机每小时可完成 200 平方米的胶缝施工，相当于 10 个工人同时手工操作的效率。而且设备操作简单，只需一人握住出胶枪，跟随需要打胶的位置移动，就能完成复杂的曲线或直线涂敷，大大减轻了工人的劳动强度。

Traditional manual glue mixing is not only time-consuming, but also requires frequent stirring, while glue dispensing machines can operate continuously and can extrude tens of meters of glue strips per minute. For example, in the installation of glass curtain walls, a glue machine can complete 200 square meters of glue joint construction per hour, which is equivalent to the efficiency of 10 workers manually operating at the same time. Moreover, the device is easy to operate, requiring only one person to hold the glue gun and follow the position where glue needs to be applied to complete complex curved or straight coating, greatly reducing the labor intensity of workers.

3. 适应多种场景，用途广泛

3. Adapt to various scenarios and have a wide range of uses

无论是高粘度的硅酮结构胶，还是低粘度的密封胶，双组份打胶机都能处理。在门窗制造中，它可以在铝合金框架与玻璃之间形成均匀的胶层，既能固定玻璃，又能阻挡雨水和灰尘；在汽车制造中，用于车身部件的密封和减震，比如车门边缘的防水胶条；在电子行业，可对精密元件进行灌封保护，防止潮气和振动影响性能。这种 versatility（多功能性）让它成为跨行业的实用工具。

Both high viscosity silicone structural adhesives and low viscosity sealants can be processed by two-component gluing machines. In the manufacturing of doors and windows, it can form a uniform adhesive layer between the aluminum alloy frame and the glass, which can both fix the glass and block rainwater and dust; In automobile manufacturing, it is used for sealing and shock absorption of body components, such as waterproof rubber strips on the edges of car doors; In the electronics industry, precision components can be sealed and protected to prevent moisture and vibration from affecting performance. This versatility makes it a practical tool across industries.

二、使用双组份打胶机的注意事项：细节决定效果

2、 Precautions for using a two-component glue machine: details determine the effect

1. 胶水与设备的 “匹配”

1. Matching glue with equipment

使用前要确认 A 胶和 B 胶是否适合该打胶机，比如粘度太高的胶水可能需要更大功率的泵系统，否则会出现出料不畅的情况。同时，两种胶水的密度差异不能太大，否则容易在混合管中分层，影响混合效果。比如 A 胶是稠状膏体，B 胶是稀状液体，需要先在胶桶中进行初步搅拌，再进入打胶机混合。

Before use, it is necessary to confirm whether A glue and B glue are suitable for the glue machine. For example, glue with high viscosity may require a more powerful pump system, otherwise there may be poor discharge. At the same time, the density difference between the two adhesives should not be too large, otherwise it is easy to layer in the mixing tube and affect the mixing effect. For example, A glue is a thick paste, while B glue is a dilute liquid that needs to be initially stirred in a glue bucket before entering the glue machine for mixing.

2. 比例校准 “很重要”

2. Proportional calibration is' very important '

新设备或更换胶水后，要进行比例校准。简单的方法是：在出胶口下方放一个空容器，开启设备让胶水流出 1 分钟，分别称重 A 胶和 B 胶的重量，计算实际比例是否与设定一致。如果有偏差，通过设备的调节按钮进行微调，直到比例准确，这一步能避免因比例错误导致的质量问题。

After new equipment or replacement of glue, proportional calibration should be performed. A simple method is to place an empty container under the glue outlet, turn on the device and let the glue flow out for 1 minute. Weigh the weight of glue A and glue B separately, and calculate whether the actual ratio is consistent with the set value. If there is a deviation, fine tune it through the adjustment button of the device until the proportion is accurate, which can avoid quality problems caused by proportion errors.

3. 清洁与安全 “别忽视”

3. Cleanliness and Safety "Don't Ignore"

每次使用完毕后，要及时清洗混合管和出胶枪，避免胶水在设备内固化。可以用专用的清洗剂或溶剂冲洗，确保没有残留。操作时要戴防护手套和护目镜，因为某些胶水具有刺激性，不慎接触皮肤或眼睛时，应立即用清水冲洗并就医。

After each use, the mixing tube and dispensing gun should be cleaned promptly to prevent the glue from solidifying inside the equipment. You can rinse with specialized cleaning agents or solvents to ensure there are no residues. Wear protective gloves and goggles during operation, as certain adhesives can be irritating. In case of accidental contact with the skin or eyes, rinse immediately with clean water and seek medical attention.

本文由双组份打胶机友情奉献.更多有关的知识请点击:http://freexvideosnow.com我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message